We will send you an email to reset your password.
- 30%
$ 21.60
$ 30.88
This non-sag adhesive is a flexible and highly versatile rubber-based compound that exhibits exceptional adhesive contact and sealant qualities
It is perfect for vertical or overhead use such as drilled holes on the underside of handrail for iron baluster installation
The tack time is approximately 4 minutes with a full cure time of 24-72 hours, depending upon amount used, temperature and humidity
Use with a standard caulk gun cartridge
Fills approximately 110 holes depending on hole size
10.2 Oz Clear Adhesive; Dries clear
- 30%
$ 2.02
$ 2.89
Designed to give a clean, finished look without the need for adhesives or shoes
Simply slide the plastic insert into the bottom of the trimmed baluster, install the dowel screw into the tread, and screw the plastic insert and baluster tight against the tread surface
For use with our 1/2-in hollow square iron balusters
Includes tapered plastic insert, dowel screw, and instructions. For open tread and level run applications
NEW
- 30%
$ 2.86
$ 4.09
Designed to give a clean, finished look without the need for adhesives or shoes
Simply install the lag of the assembled fastener into the wood tread, kneewall plate or landing tread and slide the bottom of the trimmed baluster over the fastener until the baluster is tight against the wood mounting surface.
For use with our 1/2-in hollow square iron balusters and includes instructions. For open tread stair, kneewall stair and level run applications
- 30%
$ 0.23
$ 0.33
If the balusters you purchase do not come with bottom pins and you need them, then
simply order the LJ-PIN-EZ. These are 1-3/4" deep with a 9/32" dowel pin and a 3/4" bottom pin.
You made find the LJ-3035 Centaur tool and LJ-3036 Dowel-Fast Tap handy on large jobs.
Wood Baluster Pin
Used in the predrilled hole in our "LJ" line wood balusters
Provides an alternate installation method
- 24%
$ 16.30
$ 21.73
This is the "must have" tool for all stair jobs.
Here's why.....
Our VersaTool locates holes as well as starts and tightens hex nuts onto rail bolts
Drives 5/16 rail bolts and tightens 1/2 hex nuts
Also used to locate 1/4 pilot hole on handrails & rail drops for attaching to Conect-A-Kit handrail fittings
Instructions included
- 29%
From $ 2.13
$ 3.04
LJ-3079 — Rail Bolt Kit
Use to attach handrail to; handrail, fitting, newel, wall; or fittings to fittings.
Select wood species for desired 1" diameter tapered wood plug.
To view instructions, see: http://ljsmith.com/assets/files/pdf/3079.pdf
- 30%
$ 0.84
$ 1.20
3000-3.5 - Rail Bolt - 3-1/2" (nut sold separately)
sold individually
3-1/2 inch Rail Bolt - Does not come with 5/16" threaded nut.
3-1/2-in Rail or hanger bolt
Use with 2812-FWMT and 2813-NTMT to connect handrail to: handrail, handrail fitting, newel or wall; or connect handrail fitting to handrail fitting
- 29%
$ 1.74
$ 2.48
5 inch Rail Bolt - Does not come with 5/16" threaded bolt or washer
5-in Rail or hanger bolt
Use with 2813-NTMT and S-3101 to mount wood newel posts to the floor or to fasten handrail through a rosette to the wall
- 28%
- 24%
